• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

Ottsix TKO10

Shinjari said:
When you say VVD, do you mean specifically the Vanquish products VVDs?



Any xr10 universal/cvd would work. I typically use the Axial xr10 universals and cut them down and file new tangs. I know some vendors even provide this as a service.



If you get wide tubes, then you dont have to modify the xr10 universals/cvds/vvds.



If you want to maintain roughly stock scx10 width, from my experience you either have to modify them yourself or find a vendor who sells them already modified. "thumbsup"
Click to expand...



I'm talking about these
https://www.amainhobbies.com/ssd-rc-wide-d60-hd-cvd-axle-2-ssd00104/p498785

Instead of these

http://www3.towerhobbies.com/cgi-bi...772vERXoQHvN-sDFnUGt5BmUzShLejZiKAaAscH8P8HAQ




Sent from my iPhone using Tapatalk
 
I cracked a housing today, not sure how as it was all light trailing today.....this is my third time with these out crawling.
20160604_111633_zpssm5gnsaq.jpg
 
Shinjari said:
Either should be fine for the wide setup. Probably get a little more steering with universals. But it'd be minimal. "thumbsup"
Click to expand...



When you do the wide setup in the front how do you make the rear match track width? Any way to do it other than wheel spacers?


Sent from my iPhone using Tapatalk
 
Erbing said:
I cracked a housing today, not sure how as it was all light trailing today.....this is my third time with these out crawling.
20160604_111633_zpssm5gnsaq.jpg
Click to expand...
Looks like you also have those xbeef brackets fitted also. Goes to show how much they do. Nothing at all. Fit some beeftubes and it won't happen.
 
I bought 3 cases narrow splined and standard tubes from Dan (Beeftubes). Then I read on Facebook that ottsix was discounting version 1 and releasing V2. Needless to say I was a bit disturbed just investing in the V1 set up. Hell V1 hasn't been out very long and they are already phasing them out? I sold everything new and am currently looking for my next housing. :evil::evil:
 
Don't get me wrong guys. I stand behind ottsix and what they do for our hobby. I'm all about improvement to, but dang. Release a new housing and discontinue the first a few months after release? Allot of folks dropped a ton of $ on Beeftubes etc on the first release. Not to mention Dan at Beeftube who designed some beautiful tubes for them. His machine time isn't cheap either. I thought about just stockpiling on first gen housings then thought again.
 
That's what I'll likely end up doing is just buying maybe 2 or 3 housings. Still about half the price of new beef tubes.


Sent from my iPhone using Tapatalk
 
Wonder why they are changing and what the reasoning was.

Basically any housings with beef tubes are pretty indestructible. Maybe they are going with a different plastic, or making some CMS friendly housings.
 
I don't really care too much. Someone is always the last 2 buy gen 1. I was more irritated that the only place it was announced that I could find was a tko10 Facebook fan page.


Sent from my iPhone using Tapatalk
 
That is true. I mean the trusses for the gen 1 were always a deal breaker for me. Fortunately they were perfect for my leaf sprung willies that doesn't need link or servo mounts.
 
dpcardoza said:
When you do the wide setup in the front how do you make the rear match track width? Any way to do it other than wheel spacers?


Sent from my iPhone using Tapatalk
Click to expand...

There are several methods. If you have fancy beadlocks with adjustable offsets, just put on some wider hubs. You can do the wide setup at the rear and some vendors make the correct width axle shafts as well.

I have only done the narrow mod so the track width is ~1/4" wider at each end due to the wraith/xr10 chub/knuckle being wider than the scx10 setup, so I just offset with some hubs, or even just a wider hex at the rear. "thumbsup"
 
Shinjari said:
That is true. I mean the trusses for the gen 1 were always a deal breaker for me. Fortunately they were perfect for my leaf sprung willies that doesn't need link or servo mounts.
Click to expand...
Truss remains unchanged for gen2. From the pics I saw on FB they looked identical to the 1st gen. Just extra ribbing etc on them for added strength I think.
 
Shinjari said:
There are several methods. If you have fancy beadlocks with adjustable offsets, just put on some wider hubs. You can do the wide setup at the rear and some vendors make the correct width axle shafts as well.



I have only done the narrow mod so the track width is ~1/4" wider at each end due to the wraith/xr10 chub/knuckle being wider than the scx10 setup, so I just offset with some hubs, or even just a wider hex at the rear. "thumbsup"
Click to expand...



I'll buy some 225's for the front and 475 or 600 for the rear.


Sent from my iPhone using Tapatalk
 
Not being a FB member, can anyone post the info here? Or post a link? I can't seem to find any info on Ottsix's FB, just race results.

So should I be hoarding Gen 1 housings since I have beef tubes already?
 
You must log in or register to reply here.

Similar threads

C
AX10 Scorpion RTR turned NMRCC Trail Class Build
2 3
Replies
46
Views
760
Chingon
C
Jfrisch1
Diving into an optic
3 4 5
Replies
81
Views
3K
Jfrisch1
Jfrisch1
R
Rear upper links positions
Replies
5
Views
729
Reezo
R
Thloftus
Thloftus’ Gravity Well H10 Optic kit
2 3
Replies
51
Views
2K
Thloftus
Thloftus
JatoTheRipper
Jato Gets Offerings to Build the Teal Terrifier H10 Optic
5 6 7
Replies
120
Views
6K
B-MOW71
B-MOW71
Back
Top