Losi Steering mod design

[CODYBOY]

Ok, slowly getting these done. Robbob's kit is going in the mail today!"thumbsup"
Yours is next Simon. Going to see the grandkids for the weekend, so I will finish it up Monday. If you could, PM your address for down under and we can figure the shipping. Thanks for your patience guys!"thumbsup"
Ernie

 

[pajey]

Getting excited. Ordered a servo plate from robob the other day;-)

 

[CODYBOY]

Getting excited. Ordered a servo plate from robob the other day;-)

Hey pajey, I sent you a PM requesting shipping info, yours and simo are ready to ship down under!!"thumbsup""thumbsup"
Ernie

 

[baconbits]

What size drill bit are you using on the housing?

Sent from my SM-G935V using Tapatalk

 

[Robbob]

What size drill bit are you using on the housing?

Sent from my SM-G935V using Tapatalk

I used a #40 drill bit (.098'') for drilling and tapping my C-hubs if that helps you.

http://www.littlemachineshop.com/reference/tapdrillsizes.pdf


Ill have pictures up soon of mine ... excited to be building a Losi again. "thumbsup"

 

[baconbits]

I mean the size drill bit for the tube to fit in the housing itself

Sent from my SM-G935V using Tapatalk

 

[CODYBOY]

I mean the size drill bit for the tube to fit in the housing itself

Sent from my SM-G935V using Tapatalk

Hi Derrick, 3/32" for 3mm .5 tap. "thumbsup"
Ernie

 

[Robbob]

I mean the size drill bit for the tube to fit in the housing itself

Sent from my SM-G935V using Tapatalk

Ohhhhhh :ror:

 

[84yoda]

He's asking about what drill bit you used to drill for the brass to fit between the housings. Lol

 

[CODYBOY]

What size drill bit are you using on the housing?

Sent from my SM-G935V using Tapatalk

3/8"
Sorry this was so short, I was in town and out of data on my phone. I'm sure I don't need to tell you this, but I will just in case. You need to be very careful to keep the casing lined up with your bit, you can destroy a casing very quickly. I actually use three bits for drilling them. One the same size as the ID of the casings, put the casing in a vise run the bit into the casing to get it square with the drill press. Change to a bit half way in between stock ID, drill out, then change to the 3/8" bit. Do these steps one side at a time. If you want pics I can do that! Good luck!
Ernie



Sent from my SM-G900V using Tapatalk

 

[Robbob]

Nice to leave work and get home to this ......


And let the machine run on its own to get this


"thumbsup"

 

[CODYBOY]

Nice to leave work and get home to this ......


And let the machine run on its own to get this


"thumbsup"

I like the colored screws, what are they made of, alum?"thumbsup"
Ernie

 

[Robbob]

I like the colored screws, what are they made of, alum?"thumbsup"
Ernie

Yup swapped all but one out with aluminum.

Sent from my 0PJA2 using Tapatalk

 

[simo]

What chubs are you using Rob?

Sent from my XT1068 using Tapatalk

 

[snapon boy]

Vanquish for the wraith

 

[Robbob]

What chubs are you using Rob?

Sent from my XT1068 using Tapatalk

Vanquish for the wraith

Yup what Snapon Boy said ....... "thumbsup"

 

[CODYBOY]

Ok mrG, I have your testers ready to ship. PM me your address and we can get it headed your way.
Suji you are the last of the first five. I will try and have yours done next week! I need to get up to Lunsford Racing and pick up some brass.
"thumbsup"
Ernie.

 

[suij]

No rush on mine Ernie, I'm offshore for the next month.

 

[simo]

Would the part number be VPS02005 for the c-hubs.
Looked on various sites and clearly more than 1 option.
Don't want to order the wrong part.
Might delay my build[emoji1303]


Sent from my iPad using Tapatalk

 

[Robbob]

Would the part number be VPS02005 for the c-hubs.
Looked on various sites and clearly more than 1 option.
Don't want to order the wrong part.
Might delay my build[emoji1303]


Sent from my iPad using Tapatalk

Any from this page

RC Accessories - Axial Wraith Parts - Wraith C-Hubs - Vanquish Products