TRX4 wheel fitment info

[penguin1]

Does anyone know if the SSD portal covers will work with PROLINE flatline or denali wheels?

I have the wheels, and want the SSD covers, If not I will buy SSD wheels as well but hoping to spend that cash on something else if possible.."thumbsup"

Thanks

I have the proline faultline wheels and the inner beadlock ring needs to be enlarged to gain clearance to the portal covers. Also I installed MIP 4mm axle extensions for additional clearance.

 

[BuffaloCrawler]

so with the rc4wd hex adapters i used the wheels fit but when i tighten the nut down its bottoms out on the threads and the wheels are a little loose. Like a couple thousandths of an inch of movement at most probably but its there.....do I run a washer behind the nut?! Do i need wider hexes? I didn't see anyone mention this particular issue with the rc4wd steel wagon wheels.

 

[crawlerRmy]

I didn’t have that issue with mine but I would say a washer behind the nut would be a cheap easy fix


Sent from my iPhone using Tapatalk

 

[BuffaloCrawler]

I noticed when I took the pin drive adapter off to put the hex adapter on that the hex one is narrower than the pin drive.....when i put the wheels on and look at it you can see the end of the threads are right at the face of the wheel

 

[Evo93]

so with the rc4wd hex adapters i used the wheels fit but when i tighten the nut down its bottoms out on the threads and the wheels are a little loose. Like a couple thousandths of an inch of movement at most probably but its there.....do I run a washer behind the nut?! Do i need wider hexes? I didn't see anyone mention this particular issue with the rc4wd steel wagon wheels.

I noticed certain nuts go down further on the stub than other as well as using washers. Or you could take a flare nut make the smallest counter sink you can and re thread it. Havent tried it but I think it would work.

Sent from my SAMSUNG-SM-G920A using Tapatalk

 

[BuffaloCrawler]

I ended up replacing the stock Traxxas wheel hexes with rc4wd part #Z-S1844 and everything is perfect now. I was under the assumption that I could just change from pin drive to hex drive on the back of the wheel and use the stock hexes but they were too narrow

 

[BuffaloCrawler]

http://u.cubeupload.com/DESTROYERRACER/IMG20171230144048505.jpg

 

[crawlerRmy]

That’s all I had to do was get the adapters for the back of the wheel


Sent from my iPhone using Tapatalk

 

[BuffaloCrawler]

with rc4wd wagon wheels? look very closely at the wheel face around the nut...wiggle it slowly and look closely....it very well may be loose and maybe you didn't notice....it's a very minute amount of looseness....probably a couple thousandths of an inch of movement or so but it's there and I can't imagine I'm the only one......unless I got something that was machined improperly or something strange like that....

 

[BuffaloCrawler]

also, I did not have to drill out the center hole at all for the wheel to fit on all the way like a few other people said they had to so there's that too.......

 

[treadway47025]

What width slw hubs with vanquish wheels
Is closest to stock?

 

[jfalesi]

These should fit, right? 46.5 mm inner diameter in the back, and they show it fitting the Wraith.

https://store.rc4wd.com/Rally-19-Beadlock-Wheels_p_5691.html

 

[OSRC]

Should be no problems. Looks like they'll clear the portals and the hex is fine.

 

[jwwolf3]

MOHERO Silver wheels
https://www.amazon.com/gp/product/B0756TXQ7J/ref=oh_aui_detailpage_o03_s00?ie=UTF8&th=1
DO NOT fit TRX-4 stock. Pretty serious rub on both front and back.

Some brass Treal +3mm hexes were perfect. Stance is very sexy, just a hair wider than the stock tires sat.

Editting in some nonsense so googlers might stumble across this post:

Amazon cheap mohero trx-4 trx4 mohero wheels traxxas wheel fitment mohero fitment Mohero wheels fitting trx-4 do mohero wheels fit traxxas?

 

[jwwolf3]

Also, I have gone through this thread pretty carefully and haven't seen this chart posted yet. i found it on RC4WD and it seems like an excellent quick reference for wheel specs:

https://www.beadlok.com/wheel.pdf

 

[AnimalHippie]

Anyone know if these will clear the portals and some CODYBOY wheel weights? Really like the look of them.
https://m.ebay.com/itm/1-9-Beadlock...=1.9+aluminum+beadlock+wheels&_from=R40&rt=nc

 

[CODYBOY]

Anyone know if these will clear the portals and some CODYBOY wheel weights? Really like the look of them.
https://m.ebay.com/itm/1-9-Beadlock...=1.9+aluminum+beadlock+wheels&_from=R40&rt=nc

Hey Justin, I would be careful buying any wheel with a rear beadlock ring. I know some of them out there with the rear ring will not fit over the portals. It's hard to tell by looking at the photos. "thumbsup"
Ernie

 

[AnimalHippie]

Thank you brotha!

 

[trucktrial]

Gmade MT1904 1.9 tires on INJORA beadlock (4PCS RC Rock Crawler Metal Wheel Rim for 1/10 )

https://www.aliexpress.com/wholesal...=SB_20180807085243&SearchText=injora+beadlock

They fit perfectly and the bead locks are easy to assemble. Measures 121 * 45 mm
You just have to widen the outer hole rim 1 mm, from 5mm to 6mm

Tires Gmade MT1904 1.9

 

[audiobull]

Without reading through stuff I honestly do not understand. I am a tad more confused now.
Is there a definitive list of direct fits? Maybe a list which requires a hub add on.


I am after some direct fit 2.2 wheels and tyres that I can buy without going too wrong. I do not run a body so no rubbing issues.