sniders1975
Quarry Creeper
Cool Thanks!! I will try that!
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
Official venom factory support thread
- Thread starter CRAWLINGAROUND
- Start date
sniders1975
Quarry Creeper
Hey chris it looks like there has been some problems with the axel yoke pins i broke three & i called cs & they said they dont have any of those can you look into why these things are breaking thanks!! Tom
All parts arrived thanks again for being a great company to deal with very nice products as well crawler crawls pretty good need to make a few adjustments but should be comparable to the axials. My indoor course is tight and many peaked rocks going to switch tires for the peaked rocks cant wait tonight i will go crawl again and do some tweaking.Thanks again for the great service nice crawler great company to deal with..........kasper
anyone else have problems with the joint on the driveshaft breaking, i'v broke both front and rear drive shafts, it breaks where the pin goes through the ball, the plastic emaxx drive shaft i put in the front is holding better than the steel one
Louis
Rock Stacker
ive been having alot of probelms with drive shafts and cv's breaking. But still NO reply to my emails. 
1\4elliptic toy
Quarry Creeper
ive been having alot of probelms with drive shafts and cv's breaking. But still NO reply to my emails.
Who are you emailing? I think Chris is out of town, Are you emailing the email address in the back of your manual? I have had NO issues with a super fast reply...
...
hay guys a while since my last post. was unsuccesful with putting concepts from this onto my comp robot . illegal. having problems with the diffs staying locked. anybody know of a part that could keep the lock screwed in place? building the kit was great until the first page where they wanted me to get bits my hardware stores didnt even carry. h7 hex... to small fragile. and atttempting to drive those screws in was terrible... was missing 3 screws and some threads were interlocked and ground. didnt like how everythign was unthreaded. after all its an amazing crawler. 9.8 out of 10 out of the box
very content with my purchase. give advice on locking diffs.
-me
hay guys a while since my last post. was unsuccesful with putting concepts from this onto my comp robot . illegal. having problems with the diffs staying locked. anybody know of a part that could keep the lock screwed in place? building the kit was great until the first page where they wanted me to get bits my hardware stores didnt even carry. h7 hex... to small fragile. and atttempting to drive those screws in was terrible... was missing 3 screws and some threads were interlocked and ground. didnt like how everythign was unthreaded. after all its an amazing crawler. 9.8 out of 10 out of the box
very content with my purchase. give advice on locking diffs. -me
CO_Crawler
Newbie
hey im having a problem with the pins that hold my yoke to the shaft, they keep falling out and its driving me nuts. any info is greatly appreciated!
Do you have the set screw installed with locktite?
CO_Crawler
Newbie
yea i used tons of locktite the red heavy duty stuff, the pins just keep flying out. i got some piano wire the same gauge and have been cutting pieces to fit, and its not just the driveshafts either on the steering knuckles as well. so any info anyone has let me know, thanks again
scubadaveojr
Quarry Creeper
what servo are you running?
Post some pics if you can. With it happening to both all I can think of is installation error as I have not had or heard of anyone else having that problem. Could certainly be wrong though.
Louis
Rock Stacker
Have any of you guys been breaking c hubs??? i keep managing to break c hubs, just broke another one a few mins ago, and i dont even know when i did it.
kookiemonster
Newbie
brittle axil
I have just bought one of your creepers and got some of the over heated axil can u send me some new ones you can e mail me at kookiemonster420@gmail.com
I have just bought one of your creepers and got some of the over heated axil can u send me some new ones you can e mail me at kookiemonster420@gmail.com
CO_Crawler
Newbie
Venom Aluminum Chub: AX10 Scorpion - 4022
just wondering if this hop up venom makes for the ax10 with fit my creeper, the pins were sliding i got it fixed for the most part, but one last pin slid out on the front axle steering hub and snapped the plastic c-hub, this would be a great replacement part,
just wondering if this hop up venom makes for the ax10 with fit my creeper, the pins were sliding i got it fixed for the most part, but one last pin slid out on the front axle steering hub and snapped the plastic c-hub, this would be a great replacement part,
Louis
Rock Stacker
^^^YOUR RIGHT, that would be a great replacement part, i would buy aluminum hubs, Right now i am working with thundertechracing to get mip metal drive shafts. Ill let you guys know if they will work.
CRAWLINGAROUND
Pebble Pounder
Nope just letting you know it was coming real soon and fixes the trans hang up issue. Will be standard issue and as a spare part.
Also we have strengthened the lower links a bit and labeled them in the mold so they are easier to identify. There are other small improvements to the kit as well so its easier to build.
Also we have strengthened the lower links a bit and labeled them in the mold so they are easier to identify. There are other small improvements to the kit as well so its easier to build.
Last edited:
CO_Crawler
Newbie
hey chris, do you know if that ax10 aluminum c-hub will work with the creeper? i would much rather have metal ones than plastic. thanx
Similar threads
