Knitewulfe
Pebble Pounder
Good call. Only thing to keep in mind is the sidewinder has a very weak internal BEC.
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
Shane's GMade R1 Rock Buggy Build
- Thread starter Szczerba
- Start date
Good call. Only thing to keep in mind is the sidewinder has a very weak internal BEC.
Szczerba
I wanna be Dave
yep. i have a CC BEC ready to go.
ROLANDROCKSHOP
I wanna be Dave
did the r7 goodies help with the axle swing?
Szczerba
I wanna be Dave
The axle swing you might have saw this past weekend was from the upper links coming loose on the chassis. I have since added thread locker and nuts to those connection points. Oh and the top shock mounting points. I just used little cone washers on one side to reduce the slop. no axle swing now at all.
blakeski
I wanna be Dave
this rig is awesome!!!! i want one soo bad!!! this is the one that made me want one of these!!!"thumbsup"
great job
great job
ROLANDROCKSHOP
I wanna be Dave
excellent!
you want those msd rings??
they do fit those gt 2.2 wheels.
you want those msd rings??
they do fit those gt 2.2 wheels.
Szczerba
I wanna be Dave
Thanks boss! Started fabbing up a rear box to put the ESC in (got the idea from Ripper7777777).
Sure thing. I looked at your text earlier and then got busy at work. I'll grab them in Hot Springs next weekend. Thanks.
Also, cutting some more lugs out of the rock crushers :shock:
Last edited:
Szczerba
I wanna be Dave
Started on a rear electronics box. Nothing fancy.
Also got a wild hair to cut the rears some more. Took every other row out. Yes? No? Maybe?
Reminds me of the FatGirl's orginal cut up boggers. Shiny spots on the rears are some thin spots I put some rubberized CA on to sure them up.
Also got a wild hair to cut the rears some more. Took every other row out. Yes? No? Maybe?
Reminds me of the FatGirl's orginal cut up boggers. Shiny spots on the rears are some thin spots I put some rubberized CA on to sure them up.
Attachments
That's what I did to my Flat Irons! They still crawl well, but they will suck in the mud if you don't have decent wheelspeed. :ror:
http://i460.photobucket.com/albums/qq321/helheddedcrawler/Picture233Large.jpg?t=1274990502
http://i460.photobucket.com/albums/qq321/helheddedcrawler/Picture233Large.jpg?t=1274990502
Last edited:
Szczerba
I wanna be Dave
Those look as ugly as mine
I will do the fronts when my thumb recovers from the wicked blister I got from using metal snips on rubber tires. No pain no gain.
I have since wired up a Sidewinder with the 35T motor and 12t pinion. The 14, 16,18t pinions should be in today. I will be looking for another motor option this weekend. Either a little brushless or a 19-21t brushed.
I still need to finish up the electronics box and clean up the rat's nest wiring I currently have.
ROLANDROCKSHOP
I wanna be Dave
hell see if the trax titan 12t will fit??
that'll move ya!
that'll move ya!
Szczerba
I wanna be Dave
Probably won't fit. Most of the bigger endbell 540's will not fit without some cage grinding/cutting/melting. The chassis starts to dovenose in right where the end of the endbell sits, then you run into clearance issues with the bolts for the upper links (stock).
I put a 17t pinion on the 35T for now. Nice step up from the 12t. A 20t pinion didn't seem like it would fit, no room for motor adjustment. I bet a 19t on a 540 motor is the biggest it will hold. Just guessing though. I didn't spend much time with the 20t but it seemed a no go.
I'll get some driving time tomorrow at the NWARC comp. I'll probably pick up a 21 or 19T brushed motor tomorrow after the comp, unless i can find a 2500-3500kv brushless that will fit. Might have to try a 380 sized prop motor, like elbo's.
And I cut up the front tires to match the rears.
Last edited:
ROLANDROCKSHOP
I wanna be Dave
i tried a 19t in my rock racer,it was fine until you had to go slow...
just didnt have the torque.
i got a hh revolver i might let go of??
just didnt have the torque.
i got a hh revolver i might let go of??
Szczerba
I wanna be Dave
SOme pictures
Ran the R1 on 35T and 17t pinion on Saturday. At a rip rap comp spot, so bashing was limited.
Drag brake on Sidewinder was only at 100% for bashing. It crawled good but I had to feather the throttle to get over some rocks due to the pinion size.
Took off the Aetna Mountain cuts for some rovers. The 1lb each fronts and 5oz rears (Total each tire wheel setup) made the R1 climb well. The berg offset wheels seemed to be a good width for crawling too.
Eritex berg offset with rovers.
10 5/8" or just over 10.5" wide outside of the tires.
I think it could run some comps with the sidewinder setup different and swap out the 17t pinion. Although it's more fun jumping this truck. Sixth picture down is some plastic servo horn carnage.
Video coming tomorrow.
Ran the R1 on 35T and 17t pinion on Saturday. At a rip rap comp spot, so bashing was limited.
Drag brake on Sidewinder was only at 100% for bashing. It crawled good but I had to feather the throttle to get over some rocks due to the pinion size.
Took off the Aetna Mountain cuts for some rovers. The 1lb each fronts and 5oz rears (Total each tire wheel setup) made the R1 climb well. The berg offset wheels seemed to be a good width for crawling too.
Eritex berg offset with rovers.
10 5/8" or just over 10.5" wide outside of the tires.
I think it could run some comps with the sidewinder setup different and swap out the 17t pinion. Although it's more fun jumping this truck. Sixth picture down is some plastic servo horn carnage.
Video coming tomorrow.
Attachments
Last edited:
mat
Pebble Pounder
Great Pics Shane!
How is the torque twist on yours?
What are those rims your using on your crawler set up?
Be nice to see a vid, just to compare.
How is the torque twist on yours?
What are those rims your using on your crawler set up?
Be nice to see a vid, just to compare.
Szczerba
I wanna be Dave
Torque twist is there but not too bad. I put the driver side top rear link on top of the 4-link plate to try and help.
Those are Eritex's berg offset drilled out by JeepInDoug with .50 cal's filled with lead in the fronts.
Eritex berg offset with rovers.
10 5/8" or just over 10.5" wide outside of the tires.
blakeski
I wanna be Dave
Awesome! Great looking with them bergs! You think you could scale it out more?? Like a scaler basher? Great pics bro!
ROLANDROCKSHOP
I wanna be Dave
rc4wd spooky crawlers."thumbsup"
i got a set ill let ya try on at the comp."thumbsup"
i got a set ill let ya try on at the comp."thumbsup"
Szczerba
I wanna be Dave
What you talking about adding to it, to make it more scale?
I think it looks decently scale, with the Aetna Mountain cuts on it. :ror:
Sweet.
On another note, I spent 2 hours editing a 6 minute video of this thing at a skate park, comp crawl and some general running and had an error when saving the video. I will redo it tonight.
I beat the crap out of this thing and no issues. My wife even bashed on it for a bit. I was sure she was going to break something but no.
And I figured out my MaxAmps 2200mah 11.1v lipo just fits up on the front battery plate!
I ordered this last night. And a HolmesHobbies adapter plate.
http://www.amainhobbies.com/product...ion-HK-2221-12-V2-Brushless-Motor-400W-2580Kv
...
Last edited:
blakeski
I wanna be Dave
Sorry i should have made myself more clear! lol ...i mean like coilovers and maybe lower it abit.. make it look like the cambell rig, id want this thing for a trail.basher rig...just looking for different options is all..
