Members' Rides - No talking

[hairba11]

Truck Base :Mini-LST

ESC: stock losi dual motor esc

Motor(s): two 141:1 gear reduction units
http://www.allelectronics.com/cgi-bin/item/DCM-282/400400/70_RPM_GEARHEAD_MOTOR,_USED_.html

Servo(s):futaba full size front and rear

Trans: front, direct from gearmotor to diff with driveshaft
rear, direct chain drive from gearmotor to diff input cup slotted for later this week right now it is front wheel drive

Axles:Stock rear lubricated with JB-Weld, 3 racing cranked down ball diff up front

Tires:Moab's with 3/8 inch foam and 2.2 wheels on 1:10 alloy adapters

WB:9.25in from axle to axle

Overall Width:10 in

Diff clearance:2 in

Center Chassis clearance:not much 2.5 in

Overall length:14 in

 

[Rokzilla]

Truck Base : Extended ESP Rokzilla Chassis

ESC: Rebel 2

Motor(s): Integy 55t

Servo(s): Hitec 645mg

Trans: Clodbuster

Axles: Clodbuster, Trax gear Posi

Tires: Imex Jumbo Pullers

WB: 18"

Overall Width: 16"

Diff clearance: 2"

Center Chassis clearance: 3 3/4"

Overall height: 11 1/4"

 

[ColquittCustom405]

Truck Base :Tamiya Bruiser

ESC:Novak Super Duty

Motor(s):550 can

Servo(s):Hitec/JR

Trans:Modified EMaxx

Axles:TLT

Tires:RC4WD BL's Moabs

 

[ksully]

Newbright rockcrawler
imex red rock tires 2.2
stock suspension cups removed at top of shocks
custom painted by myself

 

[Mike Poulson]

Truck Base : Associated TC3\B4

ESC: Mamba 25

Motor(s): Axi 2212\26

Servo(s): JR

Trans: Spooled B4

Axles: Spooled TC3\ B4CVD's

Tires: Moab

WB: 12"

Overall Width: 11.5"

Diff clearance: 2"

Center Chassis clearance: 2.5"

Overall height: 6.5"

 

[RydeFab]

pimping 2.2 "r2d2"
pimp slap chassis
tlt axles
r2tranny
super rooster/55t lathe
hitec 5955
spectrum rx/tx
ford f150

super pimping "c3po"
homemade torsion chassis
txt axles
e-maxx tranny/gd600/55t lathe
super rooster
hitec 5955 f/r
spectrum rx/tx
ford excursion

crawler hauler
homemade aluminum chassis
tlt axles
losi xx-t tranny
rebel 2/55t lathe
hitec 645
jr rx/tx
juggy leaf front/4 link rear
ford f650

 

[Generis]

my e-savage crawler is done

the writeup and pics are here:
www.cardomain.com/ride/628266/13
Enjoy the slow life.

 

[toomessedup]

pti goliath
lrp waterproof runner
integy 55t lathe
hitec 645mg
goliath transmission and axles
imex swamp dogs
13.5 in wheelbase
all electronics fully waterproofed

 

[CRAWLIN 4 FUN]

Truck Base :NN

ESC:NOVACK

Motor(s):65T

Servo(s):HITECH 645MG

Trans:N/A

Axles:CLOD

Tires:IMEX

WB:16"

Overall Width:14"

Diff clearance:2.25

Center Chassis clearance:4.5

Overall height:10.5

 

[G-crawler]

My Spider

Truck Base : Gmade Spider

ESC: Mamba max

Motor(s): Integy lathes 55t

Servo(s): 5645mg

Trans: None

Axles: Gmade

Tires: Imex red rocks on RC4WD 3,2" beadlocks.

2 movie clips..

http://s172.photobucket.com/albums/w20/gcrawler/?action=view&current=MOV03095.flv

http://s172.photobucket.com/albums/w20/gcrawler/?action=view&current=MOV03093.flv

 

[hairba11]

Truck Base : Wheely King

ESC: stock

Motor(s): Integy 55t

Servo(s): dual TPro995mg with reverser

Trans: stock, 13/96 gearing

Axles: stock, JB-Weld lockers

Tires: Imex K'rock

WB: 14.5"

Overall Width: 12"

Diff clearance: 2.375"

Center Chassis clearance: 4.75"

Overall height: 10.75"

I'll update when i get the lid done.

 

[Mikekx65]

my ride

Truck Base : nylint

ESC:novak xrs

Motor(s):mini-t stock

Servo(s):water proof traxxas 2055

Trans:none

Axles:nylint

Tires:nylint cut and weighted

 

[cabsover78]

Truck Base : 2wd nylint

ESC: board

Servo: stock

Motor(s): silver 280 can

Trans: stock

Axles: stock

Tires:front stock, rear stock w/studs

to bad i don't have a body.. o well got a wk 4x4 for scaler on order

 

[krikir]

Wanna see my new rig? Here it is.

My very first RC crawler (not my last!).

 

[Kranberry]

my ride
here is my super vs wk
specs:
motor:35t
wb:~14.5
radio:3 ch coming
ws(wheel steer):4ws(not shown)
body:stock soon will change to what i have no clu
wheels:stock 2.2
tires:stock chevrons, soon to be all maxx mashers
chassis: matalic red vs
~pics~

 

[mjh]

Truck Base :CLOD
ESC:TEKIN2
Motor(s):55T LATHES..8t pinions
Servo(s):645'S
Axles:CLOD..locked
Tires:RED ROCKS...ON MAXIMIZER B/L
WB:17 IN.
Overall Width:14 IN.
Diff clearance:2 1/2IN.
Center Chassis clearance:4 3/4 IN.
Overall height:11 IN.
Body:toyota hard body
Shocks:RC4WD internals

 

[krikir]

TLT-1 Bender SW3 Crawler

...and now, after the conversion to the new Bender SW3:

The custom built Delrin® links by Finish-Line-RC (www.finish-line-rc.com) of Denver, CO work perfectly:

Truck Base : Tamiya TLT-1 (Bender SW3 Chassis)

ESC: Castle Creations Mamba MAX

Motor(s): Integy Lathe 55

Servo(s): HiTEC HS-5645MG (x2)

Trans: Stampede Locked

Axles: TLT-1 Locked (bearings)

Tires: Proline® Moab 2.2 on trimmed Stampede Chrome Rims, lead in front, star cut foams

WB: 12.5"

Overall Width:10.25"

Diff clearance:1.5"

Center Chassis clearance:3.5"

Overall height: 8"

 

[Garrett]

Here is mine:








Build thread here ---> http://www.rccrawler.com/forum/showthread.php?t=28863

Gallery here ---> http://www.putfile.com/garrett85/images/117939

 

[BCV6SVT]

Turf Kreeper

Truck Base : HPI Wheely King
ESC: Traxxas XL-5
Motor: Integy 55T Matrix
Servo: Hi Tec 645
Trans: Stock WK, HPI 96 tooth spur gear, 16 tooth pinion
Axles: Stock WK
Tires: Moab 2.2 on Axial Beadlocks
WB: 13.5"
Overall Width: 11"
Diff clearance: 1.5"
Center Chassis clearance: 2.75"
Overall height: 10"

 

[Crawlerdude75]

Here is mine--

Truck Base : NN chassis from The Crawler Store

ESC: Tekin Rebel 2

Motor(s): Integy 55 turn lathe motors

Servo(s): Hitec HS645MG's

Trans: Clod

Axles: Clod

Tires: BFT (from the MGT) on stock MGT wheels

WB: 16.25''

Overall Width: 15''

Diff clearance: 2.25''

Center Chassis clearance: 5''

Overall height: About 9.75'' with body

Here is a pic, and if you get RC Driver, in the August 2007 issue on page 129 (above 2nd page of the A123 battery add), you will see this picture
(the crawler is the one in the middle btw :lol: ) --