-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
Axial 1/18 Yeti (and Yeti Score)
- Thread starter OSRC
- Start date
Brake Weight
I wanna be Dave
I installed a 2445 3000kV sensorless motor. It has a 2.3m shaft and the Losi Mini pinions have a smaller hole than the stock pinion. The stock pinion fit the 3000kV motor and it netted nearly stock speeds. So I dug around in my box of gears and found a 22tooth that fit. I had to file down the set screw so that it's clear the motor plate.
It has good low speed and a fair amount of speed now. I'm happy with it.
It has good low speed and a fair amount of speed now. I'm happy with it.
Nice quality setup for good price! "thumbsup"
Good info, thanks! "thumbsup"
Bad and good news, thanks! "thumbsup"
Any updates Monkey?
monkeyracer
I wanna be Dave
Yes,
The first prototypes came in, but were very far off dimensionally from what they needed to be. I had them re-run them with the tweaks, and those were supposed to show up Friday, but didn't, USPS shows maybe today for delivery.
I will probably have something to share tomorrow if these are dimensionally correct.
The first prototypes came in, but were very far off dimensionally from what they needed to be. I had them re-run them with the tweaks, and those were supposed to show up Friday, but didn't, USPS shows maybe today for delivery.
I will probably have something to share tomorrow if these are dimensionally correct.
TownsendTdi
Quarry Creeper
Made some new trail with the Yeti Jr in mind- bigger berms! A lot less flipping. Moving the battery foward helped too.
<iframe width="560" height="315" src="https://www.youtube.com/embed/Z7dwLsCw6Z0" frameborder="0" allowfullscreen></iframe>
My front ring and pinion is starting to slip under heave load, maybe a shim will help. I need to tear it open and check.
<iframe width="560" height="315" src="https://www.youtube.com/embed/Z7dwLsCw6Z0" frameborder="0" allowfullscreen></iframe>
My front ring and pinion is starting to slip under heave load, maybe a shim will help. I need to tear it open and check.
monkeyracer
I wanna be Dave
First functional prototypes test fit:
I need to get these installed in the yeti and get some testing done to make sure there are no problems. I expect to start a pre-order thread very soon for these. Pricing will be discussed in the upcoming thread in the vendor's section, so please do not ask in this thread.
Lavaheadache
Quarry Creeper
Are there going to be axles to accompany that beauty?
robert@castle
Quarry Creeper
I need that. The open diff makes it really hard to do anything with my JR.
Brake Weight
I wanna be Dave
Same here. I may just try some Silly Putty.
robert@castle
Quarry Creeper
Has anyone replaced the upper rear link with 2 links with balls on the end? I know it kinda acts as a natural sway bar, but I don't like the way when the axle rolls that it bends the tabs on the chassis where the link mounts. I'd like to replace all of the rear links with turnbuckles, I just wondered if anyone know of any that fit.
monkeyracer
I wanna be Dave
Testing has been going well. There are some slight tweaks to the dimensions to be made, but it looks like I will be starting a Pre-Order thread very soon for these. I'll link to that thread here when I get it posted.
TownsendTdi
Quarry Creeper
GPM has some aluminum trailing arms out
1/18 Axial Yeti Jr Aluminum Rear Lower Chassis Link Parts GPM MYT014L Black | eBay
1/18 Axial Yeti Jr Aluminum Rear Lower Chassis Link Parts GPM MYT014L Black | eBay
Lavaheadache
Quarry Creeper
Lower links aren't exactly the first thing these things need. Where is the 2 piece front bulkhead to make pinion mesh less of a guess? Where are the metal diffs and axles/shafts? We need those things, not metal trading arms... though they are nice ��
Brake Weight
I wanna be Dave
That's the easiest thing to make.
Major problem with solid lower links, you wont get any articulation out of the rear. Currently the flex in the nylon links allow for the axle to articulate while also acting as a sway bar. You make that rigid and the only thing the rear axle can do is travel up/down.
Careful buying those.
Careful buying those.
Brake Weight
I wanna be Dave
Seems like these are fading away. I run mine nearly daily for 10-15m but it's just because it's so small I leave it on the chest freezer in my garage. So it's right there for a quick spin around the driveway. All the hype before the reaease and the novelty is quickly waning.
Dbdynsty25
Pebble Pounder
Unless there is a local track that likes to run mini's the novelty of a mini version of a capable truck is always going to be a novelty. I've got a couple 1/14 Tacon Thrillers that I literally leave in the car in case one of the big cars breaks and I don't want to end my session so quick. LOL...that's about all they are good for.
svt923
I wanna be Dave
The fact they came out right before Axial lost the ability to keep anything in stock has a lot to do with it also. Hard to get excited about a truck when no one has been able to buy one for months.
