Andyjk's Toyota Landcruiser LC80

[Andyjk]

Hi all, I've done a bit of searching but can't seem to find if anyone has attempted a 313mm wheelbase on a CC01. I have found d 3D print files of brackets to assist in achieving this so I know at least 1 person out there has attempted it! Haha.

If you're aware of anyone having done this, I'd be keen to see it.

Regardless, I'm going to attempt it. I have a spare CC01 lying around and a toddler that is keen to have his own truck. So here we go!

Here's how it sits at present
photo album upload

Next to my own CC01

 

[JatoTheRipper]

Can't say I've ever seen a 12.3" wheelbase CC-01, but if anybody on this site has done it, it would be @OSRC

 

[Andyjk]

Can't say I've ever seen a 12.3" wheelbase CC-01, but if anybody on this site has done it, it would be @OSRC

Thanks mate, appreciate the info. The fact that I can't find any info on a 313mm wheelbase CC01 just makes me want to do it more. I'm confident I can achieve it, I just hope it is relatively drivable.

 

[JatoTheRipper]

Thanks mate, appreciate the info. The fact that I can't find any info on a 313mm wheelbase CC01 just makes me want to do it more. I'm confident I can achieve it, I just hope it is relatively drivable.

You're welcome. I'm sure it'll be drivable. You just may have to increase steering throw for that long wheelbase. I forget how much steering angle the CC-01 has in stock form.

 

[Andyjk]

I used some aluminium angle and drilled holes 313mm apart, attached to the outdrives and began to gwt the rear 4 links sorted. It's not perfect, but it'll work for now

 

[eddievedder]

This is definitely an interesting project. I do recall a long wheelbase CC01 build back in the day but I don’t think it was 12.3”. Maybe closer to 11.5” or so. I definitely recall some sort of chassis extension. Good luck.

 

[OSRC]

Nice work! Been a while since I've seen a cool CC01 build.

Yes I stretched one out but it was a bit narrow for the body I had planned to use so I never ran it. I did use some aluminum pieces to stretch out the chassis a little bit to give me better shock mount options as well as a spot to mount a rear bumper.

It still lives on with a new stock chassis, portals and a shortened Ecto body.

 

[Andyjk]

Got the 4 link all sorted

Obligatory flex shots

Pretty happy with it so far, still need to add some more pieces to strengthen it up a bit.

Next will be making a lengthened drive shaft

 

[Andyjk]

Got the centre drive shaft made up using an aluminium shaft from a TT01 and the stock CC01 universals. Got the idea from here if you're looking for instructions:

CC01 drive shaft extension

 

[Andyjk]

Body arrived!

Here it is with 110mm OD tyres. I feel they're perhaps a touch too big

And with 94mm tyres that I thi k are a touch too small

The wheelbase also appears to be slightly out but shouldn't be a difficult fix

Thoughts?

 

[Gula]

What are we looking width wise?
Maybe a 100-102mm tire is where it’s at? I'm going to have to keep an eye out on this thread since I have the same body, and will have a tire dilemma sometime in the future. I think i initially had injora or the rc4wd dick cepek mud toughcountry 105mm diameter or something or another tires. I'll have to have a look and report back.

 

[Andyjk]

What are we looking width wise?
Maybe a 100-102mm tire is where it’s at? I'm going to have to keep an eye out on this thread since I have the same body, and will have a tire dilemma sometime in the future. I think i initially had injora or the rc4wd dick cepek mud toughcountry 105mm diameter or something or another tires. I'll have to have a look and report back.

The bigger ones (that are stock axial SCX10 wheels) are about 40mm wide, the smaller ones are 38mm.

I just tried it with some RC4WD mud threshers that are 104mm and think I actually prefer the larger axial ones

Only issue is, they'll rub the chassis under full lock AND full compression. Not a huge issue but still annoying

I need to sort out the correct wheelbase before I make a decision. Just looking at it makes them all look wrong

 

[Andyjk]

Got the rear body mount made up today. I refused to pay Au$60 for the aluminium one designed for this body, so made one myself. The part that locks into the body doesn't have much bite, so I'm sceptical about how it'll hold up. Anyway, it's mounted and straight and I'm happy with it. I've designed it so that I can adjust its length in order to line it up correctly with the wheels