-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
Wraith Electronics box
- Thread starter The Crawl Space
- Start date
The Crawl Space
RCC Addict
honestly we've never tried to fit the wraith boxes on an SCX10, but it would hurt to try "thumbsup" We have plans for a SCX10 specific box just need to find the time to suss it all out.
This chassis is chopped down in front so don't let that mess with anyone :mrgreen:
The rear tray works great between the front shock hoops, you can drill holes through the top of the tray to "snap" over the top of the ashock hoops and hold them in place with the body pins that are used to adjust the height of the body posts :mrgreen:
Front view
The front Wraith box will fit similar in fashion but only to the first part of the front of the box. You can squeeze the box to the second larger part of the box but the shock hoops flex out which I don't advise
Here the front WRaith box on the front of the SCX10 shock hoops.
Now with this shortened chasis and wheelbase its hard to judge if the boxes will have clearance of axle mounted servo but the boxes will clear a standard wheelebase, ie; 12.3" plus if people start getting into the chassis mount servos that a pushed up to the front and perpendicular to the chassis rails the boxes will work "thumbsup":mrgreen:"thumbsup":mrgreen:"thumbsup":mrgreen:
Attachments
The Crawl Space
RCC Addict
Yes it will. the Spyder Wraith uses the same chassis as the orginal wraith "thumbsup"
wheelhead4x4
Quarry Creeper
Here are a few pics of it in my wraith
The Crawl Space
RCC Addict
I think this might be in the wrong section my friend, but most times the brushless motors come with the sensor wire "thumbsup"
The Crawl Space
RCC Addict
Ah ok, depending on how you have your running gear set up you can run the motor wires and sensor wire through the bottom of the front box. If you're concerned with waterproofing you can use some plastidip to seal the hole "thumbsup"
gbean
RCC Addict
I left a hole in the bottom of my box for servo wiring.
I did not seal the hole as it is the low point and want any moisture that may get in there to drain out.
I did not seal the hole as it is the low point and want any moisture that may get in there to drain out.
Last edited:
spankbomb
Quarry Creeper
Da Box in stock? Thanks!
The Crawl Space
RCC Addict
We are out of stock at the moment but with more on the way, I'll update here once we get a fresh batch "thumbsup"
spankbomb
Quarry Creeper
Thanks!
spankbomb
Quarry Creeper
Any ETA? Was going to place an order for some other parts today, but wanted to find out when these would be available first. Thanks!
The Crawl Space
RCC Addict
Rajah dat, we just got a fresh batch of Front and rear boxes "thumbsup"
spankbomb
Quarry Creeper
I just ordered the 100% front tray, rear tray, and rear tray cover. The items have already been packaged and waiting for parcel to pick the box up. Point being, the Crawl Space has outstanding customer service and turn around time.
Every e-mail was replied to in under 12 hours and even a phone call was returned within less than 1 hour.
I will continue to support The Crawl Space and its awesome owners. Thank you Ikaika.
Vengeance aka Jason
Every e-mail was replied to in under 12 hours and even a phone call was returned within less than 1 hour.
I will continue to support The Crawl Space and its awesome owners. Thank you Ikaika.
Vengeance aka Jason
Cale262
Rock Stacker
PM @ ya "thumbsup"
PontiacGT201
Quarry Creeper
ok didnt read through all pages. how much for both front and rear drop ins?
