Sacramento Scaler GTG/Comps

[Jrob]

I'm gonna work on editing some video tonite hopefully. I think we got some good shots of the libby gettin down! Or should I say up??

 

[stevew]

ok im going to pull the trigger and need some help.
I plan to use my axles and trans.
this is what i plan to buy from RPP
scx10 chassis
scorcher hard body
axial lock outs
axial clockable c's
axial high clearance knuckles (steering arm on top of the knuckle)

I plan on building a bunch of mods but is there anything else i should order or should order somewhere else maybe?
is there any problems with the high steer knuckles? I plan to put the servo in the frame rails.
i also plan on using some old traxxas shocks with red springs?

any info tips tricks would be great because i want to order this stuff in the morning

 

[wiseman1907]

ok im going to pull the trigger and need some help.
I plan to use my axles and trans.
this is what i plan to buy from RPP
scx10 chassis
scorcher hard body
axial lock outs
axial clockable c's
axial high clearance knuckles (steering arm on top of the knuckle)

I plan on building a bunch of mods but is there anything else i should order or should order somewhere else maybe?
is there any problems with the high steer knuckles? I plan to put the servo in the frame rails.
i also plan on using some old traxxas shocks with red springs?

any info tips tricks would be great because i want to order this stuff in the morning

lol....it will be a good rigs..."thumbsup"

 

[jscalecrawler]

ok im going to pull the trigger and need some help.
I plan to use my axles and trans.
this is what i plan to buy from RPP
scx10 chassis
scorcher hard body
axial lock outs
axial clockable c's
axial high clearance knuckles (steering arm on top of the knuckle)

I plan on building a bunch of mods but is there anything else i should order or should order somewhere else maybe?
is there any problems with the high steer knuckles? I plan to put the servo in the frame rails.
i also plan on using some old traxxas shocks with red springs?

any info tips tricks would be great because i want to order this stuff in the morning

u cn use the drivelines too, i still use my maxstone drive shafts, 3s 4 a year, havnt twisted or brokin one yet

 

[Jrob]

I would run the vanquish knuckles and c"s there right in sac and you can go pick them up. and the nicest machine work you can get in my opinion

 

[rc crawler builder]

I would run the vanquish knuckles and c"s there right in sac and you can go pick them up. and the nicest machine work you can get in my opinion

where are they located?

 

[Jrob]

where are they located?

Off Madison exit I believe. Not good at direction. My man zonkered will know I will ask him. I can drive there but don't know the street names.

 

[KBess1110]

tell you what you can have the wheels for $20 or come over and i will help you do yours




thanx

I'm slammed at work till Sunday but I'm game, how bout $15 if you just help me do mine!?!
Sent from my VS920 4G using Tapatalk 2

 

[Jrob]

Well didn't get any footage edited cause my boy T-Rock showed up and we ran some bad ass lines at the Compound here are a few pics.

 

[stevew]

u cn use the drivelines too, i still use my maxstone drive shafts, 3s 4 a year, havnt twisted or brokin one yet

yeah one shaft was cut so far that the very first rock i took it on it fell out. LOL so i have a ped with steel yokes in its place

I would run the vanquish knuckles and c"s there right in sac and you can go pick them up. and the nicest machine work you can get in my opinion

pricey stuff there

I'm slammed at work till Sunday but I'm game, how bout $15 if you just help me do mine!?!
Sent from my VS920 4G using Tapatalk 2

well hit me up and I dont need money to help you out.




ok my next problem is that i dont think the bearings for the knuckles will work on ax10 products LOL anyone know the size from the knuckle?
also thinking about doing full tube chassis instead of the scx10 frame.

edit found out the inner bearing is good and the outer bearing is to small

 

[tciappa]

Yea awsome night me and jeff tearing it up. course just getting broken in just wait till you drive by and see a 12ft mountain over your fence.

 

[zonkerd]

Come on jeff weres the vid? Lol

 

[Jrob]

Yea awsome night me and jeff tearing it up. course just getting broken in just wait till you drive by and see a 12ft mountain over your fence.

Those new tsl"s you got make your rig hook! You ran some nice lines last nite!! this was my favorite pic from last nite.

 

[wiseman1907]

who want to go to deer creek today about 5-5:30....hit me up with a text 1-916-289-0952

 

[Jrob]

Come on jeff weres the vid? Lol

I'm gonna work on it today. I put the link up. Cant wait to see the Libby jumping the wraith.

 

[Jrob]

Hey steve I have a set of vanquish knuckles. And some aluminum c"s. And a bunch of other stuff. If your interested in doing some trading. I wouldn't mind getting that brushless you don't like let me know.

 

[Jrob]

who want to go to deer creek today about 5-5:30....hit me up with a text 1-916-289-0952

We are gonna hit up the waterfall. At 12 today.

 

[wiseman1907]

We are gonna hit up the waterfall. At 12 today.

shit im at work today..i get off at 5 today..

 

[tciappa]

meet yall at the falls after my interview.

 

[stevew]

any of you local's want first stab at these parts?
dirty530crawlers has dibs on the brushless any ways hit me up. I'm looking for scale stuff for my very first scale build.1.9's,3cell,broken winch,winch controller,servo winch,like i said all scale in trade LOL

this is what i got

novak gtb with a 21.5 crawler motor
sky lipo 2200 2cell 40c got it with my rig works fine unknown life
2x zippy 2000 2 cell 45c charged twice (only selling to fund 3cells)
tlt axles with full bearings junfac steering links and junfac skid.one axle has steering mod both axles where shaved,locked,also has servo mounts
exceed tvp
unknown chassis with delrin skid drilled for ped
ped trans I can see bearings at the output shaft it is also locked
old tekin esc
axial tx/rx