Irie Products Twin Hammer ball bearing steering & upright shock tower

[Sr.Irie]

Irie's Twin hammer ball bearing bell crank steering & upright shock tower.



All parts 6061 T6 aluminum
Each bellcrank rides on two precision ball bearings for a no slop no maintenance steering
Shock tower is designed for G-made 85mm XD Piggyback shocks with no internal limiter or external bump stop to take advantage of the full travel of the shock
Geometry of linkage has been 3D modeled to have as little bumpsteer as possible, almost not measurable
Full kit $65.00 dollars shipped, Top plate and BB steering only $55 shipped 50 states


What is included?
6061 Top Plate and steering arms riding on ball bearings, assembled
Composite Shock tower
Center link consisting of two ball ends and a turnbuckle
2-M3x25mm screws, for the tie rods to bellcrank
2-M3x20mm screws, for the bellcrank arms
2-M3x14mm screws, for mounting F of top plate / F of shock tower
2-M3x12mm screws, for mounting R of top plate
2-M3x6mm screws, for mounting R of shock tower to top plate
4-M3 nylon lock nuts

For the upper shock mount reuse the factory cantilever posts
Recommended servo horn part numbers:
TLR1555 for 23T
TLR1556 for 24T
TLR1557 for 25T

Irie's GCM Tower Steering kit
$40 shipped 50 states



Included in kit
Steering arms made from 6061 riding on ball bearing two per arm
2-6061 stand offs
2-M3x22mm screws
2-M3x25mm screws
4-M3 Nylock nuts
2-M3 Large washers
2-Offset ball ends
1-Center link

Here is an install video that GCM was nice enough to do. THANK YOU

<iframe width="640" height="360" src="//www.youtube.com/embed/TYAUWT6tgA4?rel=0" frameborder="0" allowfullscreen></iframe>

Irie's Race Prepped Twin Hammers CVD Axles
$45 Shipped 50 states


Axles are cryoed for strength
then reassembled with 4037 chromoly cross pin
and lubed with molybdenum disulfide.
All together it makes a smooth running and pretty bomb proof axle.
Recommend Vaterra HD outdrives to go with the axle's part #VTR232062
Anyone who purchased axles on or before 9/7/2014 receives 1 Free rebuild if you pay shipping. Just to say thanks


Irie open rear diff axles. $25.00


Also can do complete setup rear differentials. PM if interested

Irie Products Wheel Bearing Kit $20.00 shipped 50 states



This kit covers all wheel bearings needed for the Twin Hammers, front and rear.
These bearings are precision quality rubber sealed bearings made in the U.S.A. not overseas.
Includes
2: 6mm x 12mm
6: 5mm x 10mm



For Questions or comments http://www.rccrawler.com/forum/vaterra-twin-hammers/489589-irie-products.html Or PM me for fastest response

I use PayPal invoices for payment
PM for stock status

Shipping

Shipping is included in the price if shipped to the 50 states

For Canada add $5.00 tracking included

International shipping $13.50

I will not cover lost or damaged with international shipping





More Products to come​

 

[Rootar]

Are the kits ready to go or is there any wait time? Also, does it include the drag link between the bellcranks?

 

[Sr.Irie]

Yes they are ready to ship and they come with all hardware to install.

 

[Pockets70]

Done deal. Awesome setup and will be thoroughly race tested starting with the Summer Season of U4RC.

 

[Rastaman]

think i might give this setup a try, i like the way it looks great job, even though i just recently installed the traxxas steering and blue monkey upright shock tower..irie..!

 

[Harley]

Nice execution, I'll have to keep this in mind.

 

[Sr.Irie]

Nice execution, I'll have to keep this in mind.

Thank you

 

[shimal]

Very interested in this, would there be space under the hood for a battery with this setup? if so, what size battery would fit?

 

[Sr.Irie]

Very interested in this, would there be space under the hood for a battery with this setup? if so, what size battery would fit?

The stock little battery will fit up front. I run the shorty batteries like the stock upgrade battery and I don't think they would fit right. If you check out the thread in the twin hammers section http://www.rccrawler.com/forum/vaterra-twin-hammers/489589-irie-products.html there are some more pictures.

 

[nos nut]

i would like to buy this. how do i order 1

 

[Sr.Irie]

For anyone I may have missed the kits are back in stock
To order PM me

 

[Natedog]

Great looking well thought out kit built for heavy duty.

 

[sickcivic95]

I had a few questions regarding the gcm tower kit you offer, 1. Is it in stock, 2. Is it a direct bolt on to their front tower plate, or does it require modification?

--Dan

 

[Sr.Irie]

I had a few questions regarding the gcm tower kit you offer, 1. Is it in stock, 2. Is it a direct bolt on to their front tower plate, or does it require modification?

--Dan

1:Yes I try to keep a few on hand I do run out from time to time
2:No it does not require modification to the GCM plate

Here is a link to a quick TM of install, check post #120

 

[Miksta]

I live in Australia and want the steering and upright shock mount kit you sell for $65, how much postage will I have to pay? And as a newbie how do I go about making a purchase?

 

[Doozie32]

Are there any GCM shock tower compatible steering bellcranks available at this time? Thanks! Pm sent.

 

[AndyCamuk]

;-)

Irie's Twin hammer ball bearing bell crank steering & upright shock tower.
All parts 6061 T6 aluminum
Each bellcrank rides on two precision ball bearings for a no slop no maintenance steering
Shock tower is designed for G-made 85mm XD Piggyback shocks with no internal limiter or external bump stop to take advantage of the full travel of the shock
Geometry of linkage has been 3D modeled to have as little bumpsteer as possible, almost not measurable
Full kit $65.00 dollars shipped, Top plate and BB steering only $55 shipped 50 states


What is included?
6061 Top Plate and steering arms riding on ball bearings, assembled
6061 Shock tower, you must bolt it on
Center link consisting of two ball ends and a turnbuckle
2-M3x25mm screws, for the tie rods to bellcrank
2-M3x20mm screws, for the bellcrank arms
2-M3x14mm screws, for mounting F of top plate / F of shock tower
2-M3x12mm screws, for mounting R of top plate
2-M3x6mm screws, for mounting R of shock tower to top plate
4-M3 nylon lock nuts

For the upper shock mount reuse the factory cantilever posts
Recommended servo horn part numbers:
TLR1555 for 23T
TLR1556 for 24T
TLR1557 for 25T

Irie's GCM Tower Steering kit
$40 shipped 50 states

Included in kit
Steering arms made from 6061 riding on ball bearing two per arm
2-6061 stand offs
2-M3x22mm screws
2-M3x25mm screws
4-M3 Nylock nuts
2-M3 Large washers
2-Offset ball ends
1-Center link

Irie's Race Prepped Twin Hammers CVD Axles
$45 Shipped 50 states



Axles are cryoed for strength then fully polished for smooth operation
then reassembled with 4037 chromoly cross pin
and lubed with molybdenum disulfide.
All together it makes a smooth running and pretty bomb proof axle.
Recommend Vaterra HD outdrives to go with the axle's part #VTR232062

For Questions or comments http://www.rccrawler.com/forum/vaterra-twin-hammers/489589-irie-products.html Or PM me for fastest response

Payment can be made through PayPal PM for PayPal instructions and stock status
I will ship outside the USA at buyer's expense


More Products to come​

<script charset="UTF-8" src="chrome://YTAutoHD/content/YTAutoHD.js" type="application/javascript"></script>

 

[geargrinder]

For anyone I may have missed the kits are back in stock
To order PM me

Sr irie. I m in need of the steering mod. I have the gcm upright shock kit and need your product. To complete my build. Please

 

[cooperDG123]

Anyone have any idea when the full kit willl be back in stock? Also if any has a sttering kit they want to sell shoot me a pm.

 

[gunder463]

this stuff still bein made or no? would like to pick up a full kit.