• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

GT3B Hack Question and Answer Thread

skinner said:
Yea I seen that...just didn't wanna high jack thread.. but that controller was something else!!
Click to expand...

Yea, i think thats gonna be my next personal project:mrgreen:

Probably add a blue tooth model to the gt3b and put one in that controller so i can use on or the other and have no physical connection. So leave the gt3b turned on layign near by and just carry that controller

Use the steering thing for steering, the X and [ ] paddles for fwd/reverse, i'll probably use r1/r2 for full dig then use r2/l2 for propo dig. R2 increases L2 decrease and have the dig % displayed there in the center. :twisted:
 
I'm getting close with this new manual, its taking for ever to write, hopefully it's helpful

Fullscreen%252520capture%25252012312011%25252041547%252520PM.jpg
 
I'm hoping to have the programming stuff done by tonight, and posted up for review and comments. I'll still have stuff like table of contents, bind procedures, ch mapping templates, etc.
 
On my hacked gt3b when the steering epas are set to around 135+ when I steer to the direction that has that ep my rear esc goes full throttle but anything lower its fine and I do have the latest fw to my knowledge
 
benoj said:
On my hacked gt3b when the steering epas are set to around 135+ when I steer to the direction that has that ep my rear esc goes full throttle but anything lower its fine and I do have the latest fw to my knowledge
Click to expand...

Yes, this is because the channel starts to overlap into the 2nd channel.

Its not a firmware issue, its a hardware issue. Which can't be fixed cheaply (it be alot cheaper just to get a adapter from servocity)
 
Skinner...cool thread....lots of stuff on that website


LosiKid...very good looking manual....looking forward to it.
 
One thing i don't like, and this is just on google docs for some reason, everything seems to be in bold.
 
Hey losikid, I'm in the middle of programming my gt3b. This may sound like a stimulus question, but which firmware do I use? To me, all the choices are written in a different language, lol. There's a lot to choose from and none of them look like v 4.0, v 4.2 ect, thanks man.
 
0.4.1. Download the file you got in the email from me, and then open that into STVP

actual file name is something like gt3b-ch6-0.4.1.s19 if i remember right
 
I found the email that you sent me, it wont let me download them, It is asking for a username and password. Sorry man, I'm being a pain, Im just trying to get this thing going last minute.
 
Ok, I've got the radio all done, but it seems as though my 2nd channel doesn't have any signal. If I switch the esc's from Channel 2 to 3 and vise versa, the 3rd channel is the only thing that is opperating on the reciever.
 
I switched rx's out since I have another, and now my esc try's to calibrate but says that the signal is too weak. I am trying to hook into 2 fxr's with a cc bec set at 6 volts and a fluent 3 channel rx.
 
You must log in or register to reply here.

Similar threads

Greatscott
Flysky - Fail
Replies
10
Views
1K
TacoCrawler
T
jebster
Jebster's XX10 T-REX
Replies
8
Views
1K
jebster
jebster
JatoTheRipper
Vanquish VRD Stance RTR
2
Replies
33
Views
7K
Col_Sanders
Col_Sanders
G
Flysky Noble transmitter questions - trim switch operation
Replies
0
Views
1K
garyk
G
S
4WS with Spektrum DX5C frustrations
Replies
10
Views
3K
SMT_Digger
S
Back
Top