• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

motor

  1. R

    I have problems

    Okay so after I waterproofed my truck it seems like my truck is killing my batteries a lot quicker then it use to! And I'm also have a problem with something idk if it's motor or what... but before I waterproofed my truck I could go full speed in reverse then go straight to full speed forward...
  2. T

    *****esc Crimping*****

    Hey guys. Is it safe to crimp wires onto a motor with soldering on the bit that the wire goes into Because my local hobby store says its not safe but i crimped it on and it seemed to work fine. Thanks, Tom
  3. T

    ****integy solder points*****

    Hey Guys, just a quick question. I'm half way through my safari build and i got the motor and had to connect the wires. Does the wires have to be completely opposite each other. The integy has the 4 options for you to solder and I'm not 100% sure if you have to solder them completely opposite...
  4. T

    Venom creeper help!!!

    i have just recently just bought my self a venom safari creeper and i would like to just get more out of it, 1. what are the best upgrades for this rig mainly for just crawling and occasionally going out to the bush for some scale. 2. What is the best motor for this rig 35t,45t,50t,55t,60t for...
  5. M

    Axial Wraith Tekin Motor noise in sensored mode

    I have an Axial Wraith that I'm building up with a Tekin 13.5 motor and RS Pro ESC. I would like to run in sensored mode but when I do the motor produces a weird noise and is slow to start up. I take the sensor cable out of the motor and the noise goes away. I recently purchased the Tekin...
  6. N

    Need help!!!not sure if esc or motor

    Hello everyone, I am new to the rc crawling world. I just bought a used losi night crawler. When the front tires hit my side walk or front steps of my house, it freezes, does not steer nor tries to go over the step, it's like there is no power or I ran out of power even though I have a full...
  7. C

    Lack of torque. Is it the motor or battery?

    Hey guys I'm new to crawling so I'm not sure what is happening. I just got a holmes 35t motor and installed it. Every now and then when crawling it seems to die, esp. when stuck in a tight spot that requires alot of torque. The wheels will stop spinning as if there is not enough torque to...
  8. Hardcoretam

    75t, 35t or 27t?

    Hi all, Recently got myself an SCX10. I've had an X-Trail chassied AX10 for a while but wanted something a bit more scale looking and picked up the Honcho RTR. I'm going to be running it on either 6 cells or 2s Lipo. I'm looking for really low wheel speed for better control and smoothness. I...
  9. H

    Motor options for Micro RC

    As the title suggests, I'd be grateful for some alternative motor options for the Micro RC. I've come across a few in the threads which are no longer in production [insert sad face]. I've read good things about the Predator (now DDT Predator) but was wondering if there are any more. My...
  10. C

    magic smoke?

    Hey guys, I had a quick question for ya'll. I'm a noob so bare with me. I have had my wraith for a little over a week and have had a few problems with it, the latest is smoke. I have only ran about 4 or 5 battery packs threw the wraith. Today I was driving it around in the yard, threw the...
  11. N

    new to rc crawling

    first off ive been full size wheeling for quite a few years solid axle chevy and a first gen yota I bought an exceed mad torque so far its been a good crawler changed suspension around but nothing major yet theres a clicking sound coming from the front when in forward movement but its not all...
  12. S

    rc4wd motors

    is this a good motor? 540 Crawler Brushed Motor 80T also, can you change the motor connectors to the esc to deans plugs?
  13. X

    torque brush vs brushless

    i just bought a different esc/motor set up and just trying to figure out somethings mainly the comparison of torque before it arrives so.. Its going in my wreckluse chassis with rockforce axles and losi comp crawler trans. i believe the gear ratio is about 99:1 (axles are 30:1 and i have a 13t...
  14. X

    no torque...

    i just finished putting my wreckluse together after running in to many problems, and now i go to run it and it has minimal torque.. i have motor: 55t integy esc: novak super duty xr battery:7.2 stick packs trans:losi comp crawler 13t pinion axles:rock force (30-1) so it should be comparable...
    • xiteamxi
    • Thread
    • losi comp crawler motor rock force torque transmission
    • Replies: 12
    • Forum: General Crawlers
  15. C

    Tekin fxr and 35t handwound motor?

    Hey guys what do you think of this combo any good and does it hook up to the scx10 without any extra stuff? http://www.amazon.com/Hand-Wound-Motor-Crawler-System/dp/B001PE8MFK Is It good as a lot of people say and and better than my ae1 esc which only lasted 1 week. :lmao: Thanks everyone with...
  16. C

    RC4WD motors anygood

    Hey guys are these motors any good they are only 10 bucks or are they just cheap crap http://store.rc4wd.com/540-Crawler-Brushed-Motor-35T_p_821.html Thanks everyone
  17. lordjasper1988

    new motor needed!!! help me please !!!!

    ive got a terra claw 55t in my rig atm, im going insane, i need a new motor!!! i was thinking of getting either the novak rock star 35t or the tekin 35t. any sudjestions as to which i should get? im leaning more towards the novak but i want to know if anyone has any ratings or ravings about the...
  18. D

    Anyone mounted a micro outrunner before??

    Hello all, I am curious, i have seen several threads on here with people talking about how they mounted these 5g hextronik 2000kv outrunners in their rigs, but I have yet to find an actual "How To" or tutorial on how to do it. I understand you have to remove a clip to move the motor shaft...
  19. D

    Whats your setup?

    hey everyone, just wondering if you could post what your running in your scx-10 please format as follows: motor esc battery pinion spur estimated top speed
  20. T

    RS10 540 problem

    I recently upgraded to the 540 kid from ZNO, I also installed the metal gears and the big boy kit, where the casing comes rtr. Everything works fine, but the front motor will occasionally lock up, and lose power. Shortly after, it will regain power. I appears the motor wants to work, but it wont...
Back
Top