What did you do to you SCX-10 today?

[Richterat83]

oh loads. . . .

Here's the before pic of how it was

8 channel rx, light controller, brake light/reverse light/running light controller, BEC, and wiring harnesses in the rear box with winch controller in the front box.

I should have an updated pic later tonight after re-arranging

 

[Johnnysplits]

This is how mine has been since I built it...

 

[Johnnysplits]

This is the new brick I got to replace the two...

 

[Johnnysplits]

And this is where it's going...

 

[Sailingeric]

I went out and tested my new RC4WD Irok 1.9 tires on the comp course that I struggled with last weekend with my stock tires. These tires make a big difference and where my old tires just spun, these dug in and SCX10 acted like it was nothing.
"thumbsup"

 

[lonleycreeper]

Beat on her.

 

[Jfrisch01]

Took the ol lady swimming

 

[Berman]

Weighted my front wheels, 220g in each, probably a bit excessive but it climbs like a champ!

 

[Meekster]

Upgraded my cr scx10 today


Sent from my iPad using Tapatalk

 

[T I N Y]

I made some brackets so I could mount two D ring shackles to the back of my G6.These are the mock up ones. I also made a new hook for my winch. I made it out of a finishing nail.

 

[Johnnysplits]

Got a set of titanium steering links on the way from Blue Monkey rc.

 

[T I N Y]

Got a set of titanium steering links on the way from Blue Monkey rc.

uppers and lowers?

 

[pvo_srt4]

added axial light bar to my Jeep Rubicon Unlimited

also added the 2nd light bar to my G6

 

[Gahndi]

Installed vp stage 1 kit axial universals and mounted vp kmc enduros.

And Installed crawler innovations deuces wild closed cell foam for proline tsls xls

And also Added axial universal 5 bucket light bar and axial aluminum steering linkages I had laying around.

 

[Johnnysplits]

uppers and lowers?

Steering links for the high steer knuckles.

 

[58513]

After my front wheels pointed towards each other a few times on my last crawl I made an aluminium link (just a bit of flat al. shaped up). My wheel alignment isn't that great (probably out by 3-5deg each side out wards but at least my wheels stay where I point them! Finished it off with a bit of heat shrink because the edges looked like crap lol. Also strung a bit of chain between the 2 D-shackles on my front bar. Just for giggles.

EDIT: You may also notice my sitcom LED system, or part of it. I disassembled an LED torch which gave me a switch, about 30 LEDs, a mad little LED light bar looking plastic frame and most importantly, a battery case, which Menes I can run the PEDs completely separate from the rigs main electronics!


Sent from my iPad using Tapatalk

 

[ShrinerTony]

Had to replace another Axial universal pin. 3rd one I've broken in about 6 months. Guess I found the weakest link [emoji53]

 

[mudbeast2]

Those cv's suck! Mine broke as well. Do the XR mod you will not regret it.


Sent from my iPhone using Tapatalk

 

[Richterat83]

Ordered a set of T-maxx driveshafts. Also put out a feeler thread for my HH motor and might go brushless on it.

 

[Tmaxxed]

Ordered up a hh br-xl waterproof, vanquish stage 1 kit, hitec waterproof servo, vanquish titainium drag link and tie rod, proline scaler shocks, extended hexes, and some 2.2 mudslinger xl's.