lowridinjuggalo
RCC Addict
Lol u going to try those at the next comp
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
Projects
- Thread starter limited77
- Start date
yes sir!"thumbsup"
lowridinjuggalo
RCC Addict
I have thowt bout it before they work good on the scaler
You're gonna have to peel some of those stickers off...geez advertising for competitors :roll: LOL
Seriously though...it looks good...but I'm wondering whats going on with your rear lower link...looks like it's installed wrong or it's the wrong link...not sure.
I made a few changes to mine today also...got tired of pulling the screws out of the tranny case...
Seriously though...it looks good...but I'm wondering whats going on with your rear lower link...looks like it's installed wrong or it's the wrong link...not sure.
I made a few changes to mine today also...got tired of pulling the screws out of the tranny case...
M_ENERGY
Rock Crawler
OK I have two comments :mrgreen:
1 - I guess you have to run VP SSZ Stars to be in the SCRCC scale club??
2- Ryan buy an aluminum tranny case. "thumbsup" If I need to make an order to help you with the funds let me know 8)
1 - I guess you have to run VP SSZ Stars to be in the SCRCC scale club??
2- Ryan buy an aluminum tranny case. "thumbsup" If I need to make an order to help you with the funds let me know 8)
M_ENERGY
Rock Crawler
Michael your rig is looking good and so is Ryan's. I can't wait to do some scaling with you guys again !!
TODBLDZ
Quarry Creeper
Wow. Looks good Michael. All these wraith builds. Where were you guys 2 months ago before I got addicted to short course and guns? :lmao:
Hardy har har har...I couldn't make up my mind which way to go on the trans, but I knew I didn't want to fool with the extended outputs that are usually 6 or 8mm which doesn't play well with what I already have. I chose to stick with the Wraith style trans and threw the one piece diff locker in there and have an aluminum case coming for it as well. I also installed the Robinson Gen3 slipper gear and have the beefy top shaft coming for it as well :twisted:
It's VERY close to being just about bullet proof which is a good thing 8)
I'm thinking about doing some lug trimming on these IROK tires to help them dig more. I like running a firmer foam than normal since I do have so much wheel speed to play with. I'm going to keep running them as they are and see if they change at all with more wear, but I'm thinking they're going to need some work to get them to do what I want.
It's VERY close to being just about bullet proof which is a good thing 8)
I'm thinking about doing some lug trimming on these IROK tires to help them dig more. I like running a firmer foam than normal since I do have so much wheel speed to play with. I'm going to keep running them as they are and see if they change at all with more wear, but I'm thinking they're going to need some work to get them to do what I want.
M_ENERGY
Rock Crawler
MG200 cut half of the lug off on the center tread and I thought it was pretty cool. I thought about doing it, but then I thought I will send them off to ECRC and let them guys do it :mrgreen:"thumbsup"
Derrick, I hear that there is a guy over there that does some niffty tire work."thumbsup"
M_ENERGY
Rock Crawler
Thats what I hear and I also heard turn around time was about a day too 8) that's some customer service! :ror:
I did...and this gear box is buttery smooth now. It also got a new BEEFY top shaft as well :twisted:
lowridinjuggalo
RCC Addict
Tranny looks sweet Ryan
hatefulboy
Rock Crawler
Been working on a new project lately. Thanks to some parts for ECRC and Ebay. Here is what I got so far.
you can see the start of the chassis in the back ground in the above pic.
Did a little brake caliper detail work.
you can see the start of the chassis in the back ground in the above pic.
Did a little brake caliper detail work.
lowridinjuggalo
RCC Addict
Detail on calb looks good I don't no y vp does not do it from factory it stands out a lot better. Looking good man
TODBLDZ
Quarry Creeper
Very nice Marcus. Can't wait to see it complete.
hatefulboy
Rock Crawler
Thanks guys! slow go on this one. All I've ever messed with is a wraith. So I'm trying to put a set of wraith axles under a chassis designed for SCX axles. Still waiting on my wheels from Mayhem Eng. I hope I can get the brakes to work with them. Still need to get the upper/lower links figured out too. Been asking alot of questions to alot of people and want to say thanks to all that have helped.
