Doomp's TF2 Build

[Doomp]

Sooo.. I've lurked on here for quite some time now, Gathering knowledge and such. I have acouple of scx10's that i have built so far and a losi comp that i purchased from a local member here on rccrawler, which is an amazing rig. I will post pictures of them later with specs. This is NOT a comp rig of any sort.... just a scaler/basher rig.. For Now...
BUT for now It tis business time, I Have decided to build a TF2. Put in the order earlier this evening. Goes as -

Z-S0533 Scale Diamond Plate Aluminum Sheets (2)
Z-P0025 Interco IROK Single 1.9 Scale Tire
Z-Q0025 Dick Cepek Torque 1.9" Single Internal Beadlock Wheel
Z-W0060 Dick Cepek Torque 1.9" Internal Beadlock Wheels
Z-T0054 Interco IROK 1.9 Scale Tire. X2
Z-D0031 King Off-Road Scale Piggyback Shocks w/Faux Reservoir (100mm)
Z-D0030 King Off-Road Scale Piggyback Shocks w/Faux Reservoir (110mm)
Z-S0397 Winch Hold down screws (4)
Z-S0276 Offroad 1/10 Scale Sand Ladders
VVV-S0027 Ultra Scale Hardened Steel Driveshaft (4.92"/6.29"-125mm/160mm)
VVV-S0019 Ultra Scale Hardened Steel Driveshaft (3.74"/5.1"-95mm/130mm)
Z-S0246 RC4WD Snorkel for Hilux and Mojave Body
Z-E0017 Scale Lighting System (Ver 2)
Z-S0590 Big Boss Fender Flares for Tamiya Hilux and RC4WD Mojave Body
V-RCM0003 Roof Rack and Frame for Hilux
Z-S0250 T-Box for Trail Finder, F-350, Hilux, Tundra. X2
Z-S0570 Red Super Soft Flex Leaf Springs (4)
Z-S0342 XVD Axle for Ultimate Scale Yota TF2 Axle
Z-E0011 Bulldog 9300XT Scale Winch (Black)
Z-B0032 Scale Bench Seat for Mojave Body
Z-K0042 Trail Finder 2 Truck Kit w/Mojave Body Set

Soo... This is how it stands as of now, Picking up a new argon bottle tomorrow... This is to tie over my 4X4 addiction till my 1:1 is trail worthy.
Build Will Be Begin Shortly.
Happy Holidays!

 

[Jeepfixer1]

Whew, let the sparks fly. Sounds like this one has the makings to be bad arse! Now we need pics

 

[WheelMan6]

Subscribed! "thumbsup" Can't wait to see the build.

I just placed an order similar to this for a Boyer Truggy a few months back, and have been working furiously on it ever since. A lot of fun.


-Travis

 

[Doomp]

Well It should be here this afternoon, Soo This evening its go time. Stay tuned folks.

 

[Doomp]

Here is acouple of pics of everything laid out.
I wont bore you guys with tearing the running gear down to check grease levels or lack there of. I will be sure to get lots of pics of this build... I got something real special planned for body work..

 

[WheelMan6]

Lots of goodies there "thumbsup"

I gotta say thats always one of the funnest parts, opening everything and getting started.


-Travis

 

[Doomp]

Alright small update, Got all running gear tore down and regreased with some nlgi No. 2 grease. I did not get any photos of this but when i tore down the front axle one bearing was rusted to the inner shaft ( pb blaster wouldn't break this puppy lose either) and the two washers that sit beside the c clips were also rusted. I hit the washers with some 200 grit and polished them up. And got cvds in the front although the carriers or something will need alittle work to get them to operate smoothly.
I did manage to get acouple of wheels setup to compare.

Opinions?