• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

Media added by BLKXJ 96

XR10 rear axle.

XR10 rear axle.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
014

014

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
XR10 front axle with Vanquish inner and outer knuckles.

XR10 front axle with Vanquish inner and outer knuckles.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Side by side shot, next to a Vanquish DH 1. The narrowed XR10 wheels will now work with the VP steering knuckles with out contact. Stock wheels are we

Side by side shot, next to a Vanquish DH 1. The narrowed XR10 wheels will now work with the VP steering knuckles with out contact. Stock wheels are we

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Rovers and Sedonas.

Rovers and Sedonas.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Wheel is in three pieces, the stick on wheel weights hold the two halfs togather. I ran 4 40 x 1" stainless screws through the existing holes and into

Wheel is in three pieces, the stick on wheel weights hold the two halfs togather. I ran 4 40 x 1" stainless screws through the existing holes and into

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Stock wheel narrowed to 1". The only draw back is the VP weights will not work with the narrow wheels, and the inturnal weight system will not work ei

Stock wheel narrowed to 1". The only draw back is the VP weights will not work with the narrow wheels, and the inturnal weight system will not work ei

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
.360 section cut from stock wheel.

.360 section cut from stock wheel.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Both cuts done. Rear bead lock was cut using a hand saw and then debured with a grinder.

Both cuts done. Rear bead lock was cut using a hand saw and then debured with a grinder.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
First cut. The lower section is cut off of the first wheel.

First cut. The lower section is cut off of the first wheel.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Mounted and ready. I used my drill press as a lathe to cut the .360 section out of the wheels. the tooling end is just a sharp Harbor Freight pick and

Mounted and ready. I used my drill press as a lathe to cut the .360 section out of the wheels. the tooling end is just a sharp Harbor Freight pick and

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 1
Stock wheel ready to be cut. 1.360 A 1/2" bolt fits into the hex on the back and can be chucked into the drill so it can be cut.

Stock wheel ready to be cut. 1.360 A 1/2" bolt fits into the hex on the back and can be chucked into the drill so it can be cut.

  • Media owner BLKXJ 96
  • Date added Dec 12, 2010
  • Reaction score 0
  • Comments 0
Back
Top