• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

servo help

  1. T

    SCX24 steering servo Reset (AS-1)

    Hey Everyone. I'm new here. Yesterday I bought an SCX24 Deadbolt. Its stock everything. I turned it on this morning and the front wheels are turning to the right so far that I cannot compensate with trim levels on the transmitter. Is there a way for me to electronically reset the wheels...
  2. T

    Setting up Two Position DIG on Capra - Help Please

    So this may be a totally stupid question, but I am way behind on understanding electronics. Just built a Capra with DIG function, have an SRM-315 Rx and a Spektrum DX5C Tx. I have the DIG Servo (Spektrum SX-107) plugged into the AUX1 port of the Rx. So I have tried to program a momentary...
  3. R

    Axial bomber servo destruction

    Hi everyone, I have an axial bomber that is eating through servos like crazy. I have stripped a hitec HS-7954SH servo as well as a savox 1230SG servo. I have gotten sick of replacing servos and I have $150 to spend on a servo. I was thinking the Protek 370TBL servo sounds good. Has anyone ran...
    • RR-10 guy
    • Thread
    • axial axial bomber bomber rr10 help noob servo help
    • Replies: 24
    • Forum: Newbie General
  4. S

    Steering Servo Wire Problem

    Newbie here "thumbsup" This is my RTR Bomber. So I bought a waterproof servo so I can run it really good on water and mud as well. Upon installation, I came across this problem. The wire is too short and I wanted to route the wire through the silicone gasket inside the waterproof receiver box...
  5. S

    Yeti 1/10 Kit arriving tomorrow!!! Need advice!!!

    Just ordered my Yeti kit last night and it should be delivered tomorrow. 3 weeks ago i got back into the hobby after a 20yr hiatus and I'm already purchasing my 2nd kit (first purchase was a slash 4x4 platinum). Need your advice on the Yeti: 1) What servo do you recommend (brand and/or specs -...
    • saddlesore
    • Thread
    • motor and esc new guy servo help yeti 1/10 kit
    • Replies: 8
    • Forum: Axial Yeti
  6. E

    Need help adjusting shift link on vintage 3 speed

    So I'm finally starting to put mu bruiser back together. I mocked up 2 servos and placed them just like they were before I took the car apart. The steering works great but, the shifting servo (pictured on top) will bump into the steering servo causing it to not be able to go into gear. How can I...
  7. S

    How many ohm potentiometer for servo?

    Any of you electrical engineers out there know how many ohm's I need for a standard 5-6v servo's potentiometer? The potentiometer in my Hitec 645mg broke from using too long of a servo horn screw so I'm going to try and replace it, but I don't know how many ohms are necessary. Thanks in advance! :)
  8. T

    servo saver

    Is it necessary to use a servo saver for crawling. If so, what brand or style do you prefer?
  9. lowlow

    Wtf!!?? Never had these servo problems

    Here's the deal.. Have been in the RC crawlers about three years, drive every day, and have built so many different rigs that I think I have experienced almost every problem possible. But this shit is weird.. I had a 7955 on one of my wraiths and it started acting funny, jiggering shaking...
    • lowlow
    • Thread
    • hitec 7955 servo servo help
    • Replies: 2
    • Forum: Electronics
Back
Top