• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

sensored

  1. S

    Performa P1 sensored crawler combo, any good??

    Hi Guys came across this, I can get the esc only too which is what Im really interested in does anyone know anything about it?? thanks https://www.bigsquidrc.com/performa-p1-radical-waterproof-brushless-combo-for-crawlers/ , ,(PA9360) by Per
    • Stray
    • Thread
    • esc sensored waterproof
    • Replies: 3
    • Forum: Electronics
  2. S

    is a 2 pole sensored motor ok for crawling?

    Hi Guys, Im looking at a cheap sensored set up for crawling, (its a personal challenge) I have access to a new 1750kv 2 pole sensored motor for 20usd, I believe the more poles the more torque and smoother operation? but will this matter if its sensored? keen to hear your thoughts! thanks!!
    • Stray
    • Thread
    • 2 pole cheap motor sensored
    • Replies: 29
    • Forum: Electronics
  3. D

    Sensoored brushless motor question

    Hi All. I got my first brushless motor, It is a GForce sensored 17.5 turn 2 pole. The problem is that the sensor harness that came with it has two plugs the same size. Either end will fit the motor but neither is small enough to plug into the Mamba Max pro. This is going into a crawler so...
  4. 0

    Velenion cogging?

    Hi, I'm new to this forum and new-ish to crawling, and hoping that I could get some input without being bashed. I have a velenion vxl3s in my wraith (I know it's not the ideal esc for crawling) but I put in a 17.5 sensored trinity motor to help with the cogging, and while it does seem better...
  5. U

    need high torque, sensored motor @ ~100 watts

    I would like a high torque motor (30 oz-in @ 5760 rpm) for souping up a Scorbot 3 robot arm I bought. I really need it to be sensored to allow high startup torque and to count the number of revolutions. I have spent hours searching, but haven't really found much, probably due to the odd...
  6. M

    Axial Wraith Tekin Motor noise in sensored mode

    I have an Axial Wraith that I'm building up with a Tekin 13.5 motor and RS Pro ESC. I would like to run in sensored mode but when I do the motor produces a weird noise and is slow to start up. I take the sensor cable out of the motor and the noise goes away. I recently purchased the Tekin...
  7. M

    Tekin Motor - weird noise

    I have an Axial Wraith that I'm building up with a Tekin 13.5 motor and RS Pro ESC. I would like to run in sensored mode but when I do the motor produces a weird noise and is slow to start up. I take the sensor cable out of the motor and the noise goes away. I recently purchased the Tekin...
  8. M

    Velineon VXL-3s with a Sensored motor? Can you help me?

    Hi I am running a Velineon VXL-3s with the Velineon 3500 Brushless Motor in my losi comp crawler. I started with a 17 tooth pinion and a 7.4v 5000mAh lipo. The motor and esc was running a bit hot and the rear worm drive was getting really hot. Like I could not hold my fingers on the drive shaft...
Back
Top