• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

novak

  1. B

    m2 vs "the dig"

    Other than being much simpler to install what are the pros and cons?
  2. N

    m2 dig problem????????

    Hello I have a Novak M2 dig ESC on my berg with a spektrum dx3c. I seemed to have bound everything and used the one touch set up correctly. But when I go through all of the channels the rear motor will not move? I have to flip it upside down and turn the tires to get it to rotate under its own...
  3. T

    What kinda run time?

    I currently run a Axial Scx10 with stock electronics. I get about 1-2 hours out of my 5000mah Durtrax Ni-MH. But, I'd like to put a 2S in it. So, what sort of run time would I get out of a AE Wolfpack that's 2S and 3400mah at 35c? And would that time be similair to if I had that same battery...
  4. T

    Brushed Goat?

    Just wondering guys, if I buy a Goat 3S ESC, could I run it on a Brushed Axial 27T? Thanks :)
  5. X

    Novak m2 dig issue!!

    Hey guys, i have an novak m2 dig esc paired with 2 tekin 45 turn heavy duty brushed motor, i am using the spektrum dx3c. When i try to set up the esc using the one touch button on the power switch, follow the instructions just as they are printed in the manual. But when i pull full throttle...
  6. ProjectSCX10

    Brushless System Opinion - Which is Best for MY needs?

    Ordering a Twin Hammers soon! Can't wait!! I wanna go brushless for sure though. I'll lay out what I want in general: Must stay under $200 I'll only be running 2s Must be sensored (for low end smoothness) 13.5t range No preference on waterproof or not I'll be using the Twin Hammers as a...
  7. J

    New Ridgecrest!

    I recieved my new Ridgecrest yesterday in the mail, from towerhobbies.com. I drove the ridgecrest around the house before removing the 20 turn motor and the AE-2. I installed a Novak ballistics 13.5 with 14mm rotor and a Brushless Hobbies LT4 120 amp ESC and a 18 tooth pinion gear. Now with 3s...
  8. B

    Jeep tj newbright trail rig

    This build starts with a Newbright Tj which my neighbour was throwing out, i started my build from the chassis of a RC4WD trail finder jeep edition, it started with leaf springs and i was not very impressed with them so i tore it down and built it up using custom axle mounts and 4-linked it. The...
  9. laxjj14

    burnt out my novak rooster crawler today looking for some input on the novak eiger?

    so i set up my 2.2 bully yesterday with all the elecronics in cluding dual rooster cralwer and i ran it for atleast 40 minutes so when i hooked it up today immediately one of the esc's starting burning out. so i called novak and they told me for $55 they could take the old one and replace it...
    • laxjj14
    • Thread
    • eiger novak novak rooster crawler rooster crawler
    • Replies: 5
    • Forum: Electronics
  10. S

    novak "The Dig"

    Is novaks "The Dig" any good? If not, what other dig switches are good?
  11. jeepscx10

    Novak ESC Question

    I was wondering if anyone has every used the Novak M2 Dig 3S Dual Brush ESC? If so, is it worth getting or is there a better ESC out there? I plan on running a RC4WD 35T motor in a SCX10. Thanks in advanced, Kenneth
  12. lordjasper1988

    new motor needed!!! help me please !!!!

    ive got a terra claw 55t in my rig atm, im going insane, i need a new motor!!! i was thinking of getting either the novak rock star 35t or the tekin 35t. any sudjestions as to which i should get? im leaning more towards the novak but i want to know if anyone has any ratings or ravings about the...
  13. B

    has anyone run these lately?? rooster ce

    so i need a new esc, dont want to do much soldering so i was going to get a novak rooster crawler and i was wondering if the jittering problem has been fixed??
  14. S

    EVX-2 in original E Maxx?

    Hey guys, I just fried my Novak EVX (one with orange casing). Can I run a 16.8V EVX-2 in my truck? I am just running 6 cell 4200s. Thanks
  15. T

    help!:confused about motors-what to buy?

    i currently run a 540, brushed motor, i defanatly want to upgrade, what motor should i look at? , my rig is not full comp use but more for leisure use but with performance. Novak motors any good? and if i bought a novak fifty five brushed motor for example, is there any thing else i would need...
  16. 0

    VXL + sensored motor combo?

    I was lookingat getting a SCX10 TR and wanted to put a waterproof ESC in so I figured go big or go home by getting the VXL. Since its a crawler a sensired motor would make sense. I was wondering what are some recommendations. I was thinking a novak but I have no clue what to get. Thanks
    • 02hawk
    • Thread
    • axial novak scx sensorless traxxas vxl
    • Replies: 23
    • Forum: Electronics
  17. M

    Velineon VXL-3s with a Sensored motor? Can you help me?

    Hi I am running a Velineon VXL-3s with the Velineon 3500 Brushless Motor in my losi comp crawler. I started with a 17 tooth pinion and a 7.4v 5000mAh lipo. The motor and esc was running a bit hot and the rear worm drive was getting really hot. Like I could not hold my fingers on the drive shaft...
  18. A

    Crawling with my new body

    Just got my proline rockstar body painted and shot some video of it also just installed my novak rooster crawler esc. <object width="640" height="505"><param name="movie" value="http://www.youtube.com/v/82IEjp6Idm0&hl=en_US&fs=1&color1=0x006699&color2=0x54abd6"></param><param...
    • Axisdrummer20
    • Thread
    • hb rovers novak proline rockstar venom creeper
    • Replies: 0
    • Forum: Videos!
  19. Knitewulfe

    Novak goat $#!T

    Novak goat problem. Just tried out my Novak goat brushless ESC. I have never been so disappointed with an RC product. I could have gotten an MMpro for just $20 more. I got the goat because it had a strong BEC, was sensored and most importantly it was advertised to have "features high-powered...
Back
Top