• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

gearing

  1. JatoTheRipper

    VRD Stubby Kit Motor and Gearing

    I am leaning towards eventually removing the Fusion Pro in my VRD Carbon and installing a stubby kit with short Revolver motor and AM32 ESC. This is just to get the discussion started as I have not even painted my Stance body nor have I gotten the truck out on the rocks or trails at this point...
  2. D

    Hot motor pinion gearing

    I'm pretty new, but do understand a bit of teching, I'm used to 1/8 buggies. I got myself a RTR Absima Khamba, but I've got the feeling it has a very low ratio (pretty high top speed). The motor gets hot quick, and since I've got heavier tires & rims I especially want to lower the pinion. It...
  3. Q

    Will putting a higher turn motor with the same gearing still smoke it?

    Still kind of new to the hobby, bought a 12t motor and a 21t pinion to put in my bomber because I was testing to see iust how fast I could make it, smoked the motor immediately. I was wondering if I put the stock 35t motor or even a 21t motor in it if it would smoke that motor too or will the...
  4. K

    gearing help for castle 1410 3800kv senseored

    hey guys before i start i want to say i have searched and read many post but it seems like the answers are all over the place right now im running the stock ratio and its just crazy fast im more into crawling then racing my wraith i have a arma notorious i race but what would you recommend for...
  5. A

    Torque, depending on gearing & # of motor turns

    Hi, I don't know that much about rc vehicles, an I was wondering: if you have a 55t motor with a top speed of 6kp/h and a 35t motor with the same top speed, will you have the same torque :?:
  6. A

    ReGearing Everest-10?

    First off, hello RC Crawler forum! This is my first post to this forum, although I've been a watcher for quite a while, haha ;-). I've been slowly building up my Redcat Racing Everest 10 crawler, and for the record I love it dearly. Massive, absolutely massive flex and articulation and very...
  7. 4

    brushless wraith gearing help

    i have an axial wraith and i just recently installed a castle creations sidewinder sct. i really like the motor but i'm tired of putting spur gears in it and don't know what gear ratio to choose. right now it has a 87 spur and a 15 pinion which isn't low enough to crawl. I was considering doing...
  8. S

    Gearing

    Hi Guys I've got a few questions about gearing for my Axial Wraith. I've got a Crawl master 16t and torque-master brxl on order, i'm guessing from what i've heard I will need to change my gearing. Do I get a choice on what type of gearing I use because i've heard that the wrong gearing can...
  9. D

    Scx10 project. Need opinions

    Hey So I'm about to make the jump to an scx10 dingo kit. My plan is to use everything stock to start out and replace whatever becomes weak points. I have a good servo and radio system, the question is the motor. I have a castle 2400kv 4 pole brushless motor and a MMP speed control, both with...
  10. D

    Losi NC-Running Hot & Smoking motors

    Any advice is much appreciated. I'm on my third motor with the LNC. Rooster Crawler ESC and a 45t Novak Expert Series crawling motor. 21 tooth pinion. Stock everything else when it comes to gearing. When I get it stuck...even barely stuck in rock crevices and the motor quickly goes from cool...
    • Davey
    • Thread
    • gearing novak rooster overheating smoking
    • Replies: 5
    • Forum: Newbie General
Back
Top