• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

driveshaft

  1. W

    Noob w/ WK questions

    Hey everyone, New to the forum, obviously. I got my son a Wheely King back in May and it's proved itself to be a solid little basher. That being said, I do want to make some upgrades to remedy an issue and get more speed out of it. First, the driveshafts. My son seems to get the front...
  2. J

    Driveshaft, you are the WEAKEST LINK

    First run with a 3S, my friend's kid tore up the driveshaft on my Yeti Score TT. I assume this was only a matter of time... I know there are upgrades from MIP and SSD - what are the pros/cons? Will non-TT Axial driveshafts fit the TT?
    • jfalesi
    • Thread
    • driveshaft yeti score trophy truck
    • Replies: 14
    • Forum: Axial Yeti
  3. K

    Ascender water locked driveshaft

    Anyone have suggestions on preventing Waterlock in the drive shafts? I didn't think I even drove through alot of water but clearly I drove through more water than I remember. I have an almost brand new Ascender with the F100 ,not that the body matters much. Any suggestions to keep this from...
  4. B

    Driveshaft with steep angle capability's

    i just installed gmade zero 104mm into my dingo, they are super smooth shocks. But now my driveshafts are binding. Whats the driveshaft that fits dingo wheelbase that can take a worse angle than the stock wb8 driveshaft?
  5. W

    SCX10 Drive train chatter and clocking axles

    I've been reading a lot of posts about the reasons that the front wheels/axle may chatter or shudder especially when starting to accelerate and the two causes seem to be: -- drive shafts not aligned properly so that pins are parallel (matching notches) -- angle from axles to motor too steep...
  6. B

    Dingo help

    I was just wondering what driveshafts would fit and work best for my dingo, I was also wondering where I can find 1.9 flat irons, everywhere is out of stock. Thanks
  7. E

    Motor spins, driveshafts do not...

    I just got my Axial Wraith RTR and after a charge, I set her down, pulled the trigger and it sorta moved two inches and now appears the drive shafts aren't connected to the motor because it just runs but nothing is going to the axles. Any thoughts? Take it all apart and connect something?
  8. K

    SCX10 driveshaft/suspension

    A week or so ago I bought an Axial SCX10. Stock it did exceeded my expectations. It wasn't til after I installed a larger suspension and tires that I ran into a problem. The wheels are 2.2 beadlocks with 5.5 tires. I think the suspension is 120mm adjustable. When I put the susp on and took it...
  9. X

    measurements of steel yokes

    If any one has them im wondering whats the overall diameter (biggest spot) on the yoke is. As i want to run them on my losi comp crawler trans and want to see if they clear the transmission case that close to the output shaft. Thanks"thumbsup"
  10. X

    custom driveshafts?

    Hello, so i put my rock-force axles in my wreckluse chassis and bought a comp crawler trans so i have f/r dig and im not thrilled with the losi drive shafts but the problem is the output on the losi trans is 4mm(i believe) and on my axles 6mm(i believe) and there isant much clearance on the...
  11. T

    Driveshaft/ driveline issues

    I have an SCX10 Honcho at the longest wheelbase. My stock driveshaft broke at the dog-ears. Part of the fun for me, is replacing broke plastic with nicer high end stuff. So I used this opportunity to put in quality CVD shafts. They fit fine, and seem to spin freely, BUT.. The wheels catch...
  12. X

    Venom Creeper Safari Front Driveshaft issues

    Hey Y'all, i just got a venom creeper safari for christmas and i was testing it over a few pillows. After a few times runnin over the pillows, i realised the Front wheels werent locked in. We looked underneath and the front driveshaft was off the transfer case...no big deal. we put it back on...
Back
Top