• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.
Road wheels.

Road wheels.

  • Media owner gman350
  • Date added Jan 23, 2016
  • Reaction score 0
  • Comments 0
Hmmm that don't look right.

Hmmm that don't look right.

  • Media owner gman350
  • Date added Jan 23, 2016
  • Reaction score 0
  • Comments 0
IMAG2210

IMAG2210

  • Media owner gman350
  • Date added Jan 23, 2016
  • Reaction score 0
  • Comments 0
Stock rear end after not very many runs. Apparently the metal these gears are made out of is only slightly harder than axial's plastic parts.

Stock rear end after not very many runs. Apparently the metal these gears are made out of is only slightly harder than axial's plastic parts.

  • Media owner gman350
  • Date added Jan 23, 2016
  • Reaction score 0
  • Comments 0
Then I ground a flat on the shaft of the bolt and threaded a M3 set screw into the boss in the knuckle carrier AX80106.

Then I ground a flat on the shaft of the bolt and threaded a M3 set screw into the boss in the knuckle carrier AX80106.

  • Media owner gman350
  • Date added Jan 18, 2016
  • Reaction score 0
  • Comments 0
I cut the threads and nut off the lower knuckle bolt AX31110.

I cut the threads and nut off the lower knuckle bolt AX31110.

  • Media owner gman350
  • Date added Jan 18, 2016
  • Reaction score 0
  • Comments 0
JConcepts G-Locs on ProLine F11 wheels.

JConcepts G-Locs on ProLine F11 wheels.

  • Media owner gman350
  • Date added Jan 18, 2016
  • Reaction score 0
  • Comments 0
2 speed trans was missing shifts. Red arrows show where it was getting worn. Shift servo was set correctly but I wasn't letting off the throttle whe

2 speed trans was missing shifts. Red arrows show where it was getting worn. Shift servo was set correctly but I wasn't letting off the throttle whe

  • Media owner gman350
  • Date added Jan 18, 2016
  • Reaction score 0
  • Comments 0
ProLine Sand Paw 2.2 tires on front on stock RTR rims. ProLine Sand Paw 3.8" on rear on ProLine F11 wheels. Stock RTR tire/wheel in the middle.

ProLine Sand Paw 2.2 tires on front on stock RTR rims. ProLine Sand Paw 3.8" on rear on ProLine F11 wheels. Stock RTR tire/wheel in the middle.

  • Media owner gman350
  • Date added Jan 18, 2016
  • Reaction score 0
  • Comments 0
Castle BEC mounted. Siliconed the ends to water proof, mounted with hot melt glue.

Castle BEC mounted. Siliconed the ends to water proof, mounted with hot melt glue.

  • Media owner gman350
  • Date added Jan 18, 2016
  • Reaction score 0
  • Comments 0
gman350

Axial Yeti RTR

  • Items 10
  • Album owner gman350
  • Date created
There are no comments to display.

Album information

Album owner
gman350
Date created
Item count
10
View count
34
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

gman350

gman350

Media items
54
Albums
4
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top